Tutorial:Porta agujas de Fresa / Tutorial:Strawberry needle holder

in Hive Diy2 years ago

Hola amigos feliz fin de semana para todos un abrazo desde la distancia , el día de hoy les quiero compartir una manualidad que realice para no extraviar mis agujas o alfileres (un parta agujas) ,me inspire en una rica fresa ,se que al igual que yo muchos de ustedes aman está fruta ,a continuación les mostraré todo lo que utilice y como lo realice

Hello friends happy weekend to all a hug from afar, today I want to share a craft that I made to not lose my needles or pins (a needle stopper), I was inspired by a rich strawberry, I know that like me many of you love this fruit, then I will show you everything I used and how to do it.

IMG_20220806_110315.jpg

Materiales que utilice:
-Semilla de aguacate
-Pintura color rojo
-Foamis (Verde y negro )
-Silicon
-Tijera
-Pincel

Materials used:
-Avocado seed
-Red paint
-Foamis (Green and black )
-Silicon
-Scissors
-Brush

IMG_20220806_093336.jpg

Pasos a seguir:
Iniciaremos pintando nuestra semilla de aguacate ,en este caso utilizaremos la pintura color rojo porque las fresas son de este color , para no pintar el mantel les recomiendo que utilicen como base un cartón o algo plástico como lo hice yo ,luego que nuestra semilla esté pintada la vamos a llevar al sol el tiempo necesario para que seque lo suficiente , una vez que seque aplicamos dos o tres capas para que quede bien pintada

Steps to follow:
We will start painting our avocado seed, in this case we will use red paint because strawberries are this color, to avoid painting the tablecloth I recommend that you use as a base a cardboard or something plastic as I did, after our seed is painted we will take it to the sun long enough to dry enough, once dry apply two or three coats to be well painted.

IMG_20220806_093754.jpg

Tomamos el recorte de foamis color verde y en el vamos a pintar las hojas que lleva la fresa arriba ,estás hojas siempre son puntiagudas haremos como una especie de solecito

We take the green foamis cutout and we will paint on it the leaves that the strawberry has on top, these leaves are always pointed, we will make a kind of a sunny shape.

IMG_20220806_103908.jpg

Seguido de este paso continuaremos sacando la forma que dibujamos con nuestra tijera

Following this step, we will continue to remove the shape we drew with our scissors.

IMG_20220806_104056.jpg

Para que el foamis se ablande y ses fácil de moldear tomé mi encendedor de cocina y lo calenté con el ,de este modo las hojas quedarían hacia abajo y no levantadas

To make the foamis softer and easier to shape, I took my kitchen lighter and heated it with it, so that the leaves would be downwards and not lifted up.

IMG_20220806_104245.jpg

Luego con el mismo recorte del foamis verde realice un pequeño tallo y lo pegue en la parte de arriba en todo el centro de las hojas

Then with the same green foamis cut out, make a small stem and glue it to the top in the center of the leaves.

IMG_20220806_104653.jpg

Una vez lista la hoja de mi fresa continúe pegándolo en todo el centro de la semilla colorada

Once my strawberry leaf is ready, continue gluing it all over the center of the colored seed.

IMG_20220806_105353.jpg

Con el foamis negro recortaremos las semillas de la fresa , estás semillas las realizaremos en forma de gotitas de agua

With the black foamis we will cut out the seeds of the strawberry, these seeds will be made in the form of water droplets.

IMG_20220806_105820.jpg

Luego vamos a continuar pegando cada semilla al rededor de la fresa ,cada semilla debe ir un poco separada de la otra para que pueda apreciarse bien lo que en realidad es (una fresa )

Then we will continue gluing each seed around the strawberry, each seed should be a little separated from the other so that you can see what it really is (a strawberry)

IMG_20220806_110048.jpg

De este modo finalice mi adorable porta agujas en forma de fresa , tomé las fotos con mi celular Redmi 9C y traduci todos los textos con el traductor DeepL , que pasen buenas tardes gracias por su atención

This is how I finished my adorable strawberry-shaped needle holder, I took the pictures with my Redmi 9C cell phone and translated all the texts with the translator DeepL , have a nice evening, thank you for your attention.

IMG_20220806_110547.jpg

Sort:  

Que Cuchi y lindo ha quedado tu porta agujas amiga 🥰🥰✨✨

Gracias bella

Thank you for sharing this amazing post on HIVE!
  • Your content got selected by our fellow curator @rezoanulvibes & you just received a little thank you via an upvote from our non-profit curation initiative!

  • You will be featured in one of our recurring curation compilations and on our pinterest boards! Both are aiming to offer you a stage to widen your audience within and outside of the DIY scene of hive.

Join the official DIYHub community on HIVE and show us more of your amazing work and feel free to connect with us and other DIYers via our discord server: https://discord.gg/mY5uCfQ !

If you want to support our goal to motivate other DIY/art/music/homesteading/... creators just delegate to us and earn 100% of your curation rewards!

Stay creative & hive on!