My experience with epoxy resin - La mia esperienza con la resina epossidica

in Discovery-it4 years ago

Hello everyone and welcome back to my Blog!

Today I would like to talk to you about one of my favorite pastimes: working with epoxy resin. I started a few years ago and I must say that it gives me a lot of satisfaction.

For the most part, I make pendants and keychains which I then gift to friends and relatives, but I also created something to keep for myself.

In this post, I will make a brief introduction by saying what epoxy resin is and how it is prepared, to then evaluate the main problems related to its use and talk about some artistic project that can be made with it.

45a.jpg

Introduction

Chemically, epoxy is a two-component thermosetting liquid polymer. Let's take a closer look at these terms:

  • Two-component: When purchasing epoxy resin, we are provided with 2 bottles, A and B. The first contains the resin, the second is the hardener, or the catalyst;
  • Thermosetting: When the mixture of A and B is exposed to a temperature higher than 10 °C, a chemical reaction begins which leads to the passage of the aggregate state from liquid to solid.

By solidifying, the epoxy resin becomes a material very similar to plexiglass, transparent and shiny.

It can be used, for example, for:

  • Cover surfaces to be restored such as wooden tables;
  • Making jewelry;
  • Making key rings;
  • Modeling;
  • Decorate or create furniture and design components;
  • Protect paintings or canvases by casting of the resin;
  • ...

45h.jpg

Preparation

Here is what we need to prepare the epoxy resin:

  • Bottles A and B containing resin and hardener;
  • Electronic scale for weighing in grams;
  • Wooden or plastic spatula;
  • Glass or container to mix the resin;
  • Protective mask: The resin, especially in the liquid state, releases volatile substances which can be toxic. Pay close attention!;
  • Protective gloves: The above substances can create a serious allergic reaction in contact with the skin and, in any case, it is good not to touch the resin with your hands. Also, let's not forget that epoxy resin is flammable.

By often working in contact with chemicals, I am comfortable with epoxy. But if this is not the case for you, I recommend paying the utmost attention and precaution! In fact, as we can see, the toxicity symbols are clearly highlighted on the bottles:

45b.jpg

In addition to what has been mentioned above, the following may be useful for artistic resin:

  • Powder pigments or liquid colors to mix with the resin. Attention, the pigments must not be water based because the latter does not allow the resin to polymerize properly! So, go ahead with oily, alcoholic and enamel bases, but pay attention to acrylic colors;
  • Glitter, golden leaves and other decorative elements;
  • Stencils of different shapes and sizes.

45c.jpg

If, as in my case, you like the idea of creating jewelry and key rings, I recommend that you also get hooks and chains of different colors and sizes so that you can give vent to creativity.

45d.jpg

Mixing and pouring

The mixing and pouring procedure is undoubtedly the most delicate moment of resin processing.

Here are all the steps to follow:

  • Weighing: First of all, it is necessary to calculate the correct amount of components A and B to mix together. The proportions are variable and depend on the resin manufacturer, but the resin is almost always in a greater quantity than the hardener. In my case, the ratio is 100: 60, therefore, for example, for 40 grams of component A I will have to add 24 grams of component B;
  • Mixing: This is perhaps the most important step in the whole process. In fact, once component A and B are placed in the glass or container, it is necessary to mix vigorously with the spatula for at least 3 minutes. Although it may seem that the solution is homogeneous already after 1 minute, it is necessary to continue because at the molecular level it is important that everything is mixed in the right size;
  • Optional step: If you want to color the resin or add the components I mentioned above, now is the time. In fact, if this is done after pouring, a homogeneous result may not come;
  • Casting: It consists in sliding the liquid resin into the mold. You can help yourself with a spoon or with a wooden or plastic spatula. This step must be carried out very slowly to avoid the formation of bubbles. If there are, I recommend breaking them gently with a tool such as a wand or straw.

The consistency of the resin in the mold should be similar to that of honey.

45e.jpg
Photo by Steve Buissinne from Pixabay

Hardening and finishing

Once the resin has been placed in the mold, all that remains is to wait for it to cure and harden.

The time required for complete transition to solid state depends on some factors:

  • Temperature: The higher the temperature, the shorter the time required for hardening. In general, it can be said that every 10 ° C more, the polymerization time is halved;
  • Formulation: An epoxy resin with the right proportions of A and B, should begin to harden in a few hours. If this does not happen, there may have been an error in the calculation or mixing.

Personally, I work the resin at home, in a well-ventilated room, and therefore the temperature fluctuates from 10 to 25 ° C according to the seasons. In about 24 hours I have always found the solid compound.

Once the resin has hardened, it is time to remove it from the mold and finish:

  • With some sandpaper, starting from the largest to the finest grain, small imperfections and defects can be eliminated. The same result can be obtained with an electric cutter;
  • There are products on the market for polishing or to obtain special effects such as the matt effect;
  • If necessary, the product can be pierced very delicately so as not to damage the entire structure.

45f.jpeg

Possible problems

  • Thickness: There are different types of epoxy resins, but not all are suitable for thicknesses greater than 1 cm. For this reason, it is recommended, in the case of large thicknesses, to repeat several castings one on top of the other instead of making a single one but with a large mass;
  • Patience: The resin tends to harden first outside and then inside, and this means that it would be better not to touch the work until it has completely hardened (or at least for a few hours) to avoid deformation;
  • Yellowing: Epoxy resin, with age, can yellow when exposed to the sun. What is anomalous, however, is whether yellowing or blackening occurs when the resin has just been made. This is almost always due to the presence of water in the resin. For example, let's say that you want to insert the petal of a rose inside a creation: the petal must be completely dried and with no trace of water. Here are my dried leaves ready to work with resin:

45g.jpg

Future projects

My favorite works with epoxy are those involving nature: leaves, flowers, seeds and fruits.

For this reason, given that spring has just ended and the plants are in full vegetative period, I am starting to dry numerous components of the natural world so that I can insert them in my works with epoxy resin:

  • Petals of Rhododendron obtusum;
  • Traps of Dionea muscipula;
  • Cannabis indica flower;
  • Rose petals;
  • Rosemary, Sage, Thyme and Mint leaves;
  • ...

Everything should be ready in a few months and I can't wait to get to work. Obviously, I will keep you updated!

45i.jpg

I hope you enjoyed this post on epoxy resin and I have aroused the curiosity to try this beautiful technique.

Thanks for stopping by on my blog.

See you next time,

Delilha


ITA

Ciao a tutti e bentornati sul mio Blog!

Oggi mi piacerebbe parlarvi di uno dei miei passatempi preferiti: lavorare con la resina epossidica. Ho iniziato ormai qualche anno fa e devo dire che mi dà molte soddisfazioni.

Per la maggior parte, realizzo ciondoli e portachiavi che poi regalo ad amici e parenti, ma ho creato anche qualcosa da tenere per me.

In questo post, farò una breve introduzione dicendo cos’è la resina epossidica e come si prepara, per poi valutare i principali problemi relativi al suo utilizzo e parlare di qualche progetto artistico realizzabile con essa.

45a.jpg

Introduzione

Chimicamente, la resina epossidica è un polimero liquido bicomponente termoindurente. Vediamo meglio questi termini:

  • Bicomponente: Quando si acquista la resina epossidica, ci vengono forniti 2 flaconi, A e B. Il primo contiene la resina, il secondo è l’indurente, ovvero il catalizzatore;
  • Termoindurente: Quando la miscela di A e B viene esposta a una temperatura maggiore di 10 °C, inizia una reazione chimica che porta al passaggio dello stato di aggregazione da liquido a solido.

Solidificando, la resina epossidica diventa un materiale molto simile al plexiglass, trasparente e lucido.

Può essere utilizzata, ad esempio, per:

  • Rivestire superfici da restaurare come tavolini di legno;
  • Realizzare gioielli;
  • Realizzare portachiavi;
  • Modellismo;
  • Decorare o creare componenti di arredo e design;
  • Proteggere quadri o tele attraverso una colata;

Preparazione

Ecco di cosa abbiamo bisogno per preparare la resina epossidica:

  • Flaconi A e B contenenti resina e indurente;
  • Bilancia elettronica per pesare in grammi;
  • Spatolina di legno o plastica;
  • Bicchiere o contenitore dove andare a mescolare la resina;
  • Mascherina protettiva: La resina, soprattutto allo stato liquido, rilascia delle sostanze volatili che possono essere tossiche. Prestare molta attenzione!;
  • Guanti protettivi: Le sostanze di cui sopra possono creare una grave reazione allergica a contatto con la pelle e, in ogni caso, è bene non toccare la resina con le mani. Inoltre, non dimentichiamo che la resina epossidica è infiammabile.

Lavorando spesso a contatto con sostanze chimiche, sono a mio agio con la resina epossidica. Ma se per voi non fosse così, consiglio di prestare la massima attenzione e precauzione! Infatti, come possiamo vedere, sui flaconi son ben evidenziati i simboli di tossicità:

45b.jpg

Oltre a ciò che è stato menzionato sopra, possono essere utili, per la resina artistica:

  • Pigmenti in polvere o colori liquidi da miscelare alla resina. Attenzione, i pigmenti non devono essere a base di acqua perché quest’ultima non consente alla resina di polimerizzare in modo corretto! Quindi, via libera a basi oleose, alcoliche e smalti, ma attenzione ai colori acrilici;
  • Brillantini, foglie dorate e altri elementi decorativi;
  • Stampini di diverse forme e dimensioni.

45c.jpg

Se, come nel mio caso, vi piace l’idea di creare gioielli e portachiavi, vi consiglio di procurarvi anche dei gancetti e delle catene di diversi colori e dimensioni in modo da poter dare sfogo alla creatività.

45d.jpg

Miscelazione e colatura

La procedura di miscelazione e colatura è senz’altro il momento più delicato della lavorazione della resina.

Ecco tutti gli step da seguire:

  • Pesata: Prima di tutto, è necessario calcolare la corretta quantità di componenti A e B da mescolare insieme. Le proporzioni sono variabili e dipendono dal produttore della resina, ma la resina è quasi sempre in quantità maggiore dell’indurente. Nel mio caso, il rapporto è 100:60, quindi, ad esempio, per 40 grammi di componente A dovrò aggiungere 24 grammi di componente B;
  • Miscelazione: Questo è forse lo step più importante di tutto il processo. Infatti, una volta posti componente A e B nel bicchiere o contenitore, è necessario mescolare vigorosamente con la spatolina per almeno 3 minuti. Anche se può sembrare che la soluzione sia omogenea già dopo 1 minuto, bisogna continuare perché a livello molecolare è importante che tutto sia miscelato nella giusta misura;
  • Step facoltativo: Se si vuole colorare la resina o aggiungere i componenti che ho citato sopra, è questo il momento. Infatti, se ciò si effettua dopo la colatura, potrebbe non venire un risultato omogeneo;
  • Colatura: Consiste nel far scivolare la resina liquida nello stampo. Ci si può aiutare con un cucchiaino o con una spatolina di legno o plastica. Questo step va eseguito molto lentamente per evitare la formazione di bolle. Nel caso ci fossero, consiglio di romperle con delicatezza con uno strumento come una bacchetta o una cannuccia.

La consistenza della resina nello stampo dovrebbe essere simile a quella del miele.

45e.jpg
Foto di Steve Buissinne da Pixabay

Indurimento e rifinitura

Una volta che la resina è stata posta nello stampo, non resta altro che aspettare che polimerizzi e indurisca.

Il tempo necessario affinché si abbia il completo passaggio allo stato solido dipende da alcuni fattori:

  • Temperatura: Maggiore è la temperatura, minore sarà il tempo necessario per l’indurimento. In generale, si può dire che ogni 10 °C in più, il tempo di polimerizzazione dimezza;
  • Formulazione: Una resina epossidica con le giuste proporzioni di A e B, dovrebbe cominciare a indurire già in qualche ora. Se ciò non avviene, potrebbe esserci stato un errore nel calcolo o nella miscelazione.

Personalmente, lavoro la resina in casa, in una stanza ben areata, e dunque la temperatura oscilla da 10 a 25 °C a seconda delle stagioni. In 24 ore circa ho sempre ritrovato il composto solido.

Una volta che la resina è indurita, è il momento di toglierla dallo stampo ed eseguire la rifinitura:

  • Con alcune carte vetrate, partendo dalla grana più grossa sino a quella più fine, si possono eliminare piccole imperfezioni e difetti. Lo stesso risultato si può ottenere con una fresa elettrica;
  • In commercio esistono dei prodotti per la lucidatura o per ottenere effetti particolari come l’effetto opaco;
  • Se necessario si può forare il prodotto, con molta delicatezza per non danneggiare l’intera struttura.

45f.jpeg

Possibili problemi

  • Spessore: Esistono diversi tipi di resine epossidiche, ma non tutte vanno bene per spessori maggiori di 1 cm. Per questo motivo, si consiglia, in caso di grossi spessori, di ripetere più colate una sopra all’altra anziché farne una unica ma di grande massa;
  • Pazienza: La resina tende a indurire prima all’esterno e poi all’interno, e ciò comporta che sarebbe meglio non toccare il lavoro fino a completo indurimento (o almeno per qualche ora) per evitare deformazioni;
  • Ingiallimento: La resina epossidica, con gli anni, può ingiallire se esposta al sole. Ciò che è anomalo, invece, è se l’ingiallimento o l’annerimento avvengono quando la resina è stata realizzata da poco. Questo è dovuto quasi sempre alla presenza di acqua nella resina. Ad esempio, poniamo il caso che si voglia inserire il petalo di una rosa all’interno di una creazione: il petalo dovrà essere completamente essiccato e con nessuna traccia d’acqua. Ecco le mie foglie essiccate pronte per i lavori con la resina:

45g.jpg

Progetti futuri

I miei lavori preferiti con la resina epossidica sono quelli che coinvolgono la natura: foglie, fiori, semi e frutti.

Per questo motivo, dato che la primavera è appena terminata e le piante sono in pieno periodo vegetativo, sto mettendo a essiccare numerosi componenti del mondo naturale in modo da poterli inserire nei miei lavori con la resina epossidica:

  • Petali di Rhododendron obtusum;
  • Trappole di Dionea muscipula;
  • Fiore di Cannabis indica;
  • Petali di Rosa;
  • Foglie di Rosmarino, Salvia, Timo e Menta;

  • Tra qualche mese dovrebbe essere tutto pronto e non vedo l’ora di mettermi al lavoro. Ovviamente, vi terrò aggiornati!

45i.jpg

Spero vi sia piaciuto questo post sulla resina epossidica e di aver suscitato la curiosità di provare questa bella tecnica.

Grazie per essere passati sul mio Blog.

Alla prossima,

Delilha


Support3.jpg

Sort:  

Manually curated by goldendawne from the Qurator Team. Keep up the good work!

Thank you very much @goldendawne :) have a beautiful day!

awwwwwwwwwwwwww, the finish is very beautiful, just enough to surround the candles with fabric and you get something very elegant, I liked this post

Thank you very much!! :) I'd like to try to do something more "gothic and mysterious", I'll let you know!

eddai non lo sapevo di queste tue passioni, non vedo l'ora di vedere le foglie e i fiori. Brava un abbraccionissimo.

Grazie mille Armando! E' bello ricevere supporto! :) a presto

Oh ... it was a time when I made necklaces with epoxy. seeing his share made me feel at home :).. good work!

Thank you very much for stopping by on my post <3

I think that working with epoxy is a really relaxing and beautiful hobby. It would be great to see your works!!

Have a nice day, bye :)

I loved this! Resin art is awesome and I saw some cool combinations with wood. I also saw something like a vacuum machine, where you can put the resin mixture to get the air bubbles out.

Making handmade resin jewelry must be fun, thank you for sharing!

che post delizioso!

🤗 grazie mille!

Molto belli i tuoi lavori e molto interessante il tuo post.
Aspetto di vedere il risultato con le foglie secche.
Brava davvero :)
!BEER

 4 years ago (edited) 

Grazie mille per il tuo supporto, lo apprezzo molto! È un hobby che richiede molta pazienza e tempo, anche solo per seccare le foglie ci sono voluti 2 mesi... Ma spero darà soddisfazioni :) una buona giornata!!

!discovery 30

You need to stake more BEER (24 staked BEER allows you to call BEER one time per day)


This post was shared and voted inside the discord by the curators team of discovery-it
Join our community! hive-193212
Discovery-it is also a Witness, vote for us here