ESP-ENG] / Hermosos dije con piedra de playa y alambre de cobre / Beautiful pendant with beach stone and copper wire /@alexanderflx

in Hive Diy2 years ago

Es hora de consentir a las chicas de nuestro hogar , dije echo con piedra de playa y alambre de cobre

It's time to pamper the girls in our home, I said made with beach stone and copper wire

IMG_20220601_163333.jpg

Hola feliz día para todos espero se encuentren bien, el día de hoy les quiero compartir con ustedes como hacer un dije con forma de árbol solo con una piedra de playa piedras de bisutería y un poco de alambre de cobre es muy fácil y muy creativo solo debemos de tener un poco de creatividad y mucho amor a lo que hacemos y les aseguro que todo lo que sigamos nos quedará muy bien, bueno sin más que decir pasaremos al paso a paso .

Hello happy day to all I hope you are well, today I want to share with you how to make a tree-shaped pendant only with a beach stone, jewelry stones and a little copper wire, it is very easy and very creative we just have to have a little creativity and a lot of love for what we do and I assure you that everything we follow will be very good, well without further ado we will go step by step.

Que necesitamos .

What do we need.

IMG_20220601_162947.jpg

  • una piedra de playa
  • piedras de bisutería
  • alambre de cobre gruesa y fina
  • pinzas

a beach stone
jewelry stones
coarse and fine copper wire
tweezers

comencemos con el paso a paso

let's start with the step by step

Paso 1: Empezemos con nuestro primer paso, para este paso tomaremos el trozo de alambre delgado y le daremos un poco de vuelta pero solo en el medio dejaremos las puntas sueltas después pondremos las puntas en pareja ya listo el alambre tomaremos nuestra piedra y le pondremos el alambre primero uniremos dos puntas y y asi vamos a unir todas las puntas de un extremo si no podemos unir todas no importa esperaremos hacer el otro lado para poder apretar todo y terminar de unir..

Step 1: Let's start with our first step, for this step we will take the piece of thin wire and we will give it a little twist but only in the middle we will leave the ends loose then we will put the ends in pairs and the wire is ready we will take our stone and we will put the wire first we will join two ends and and so we are going to join all the ends of one end if we cannot join all of them it does not matter we will wait to do the other side to be able to tighten everything and finish joining.

IMG_20220601_163302.jpg

IMG_20220601_163203.jpg

Paso 2: Para nuestro otro extremo también pondremos las puntas en pareja y le pondremos nuestras piedras de bisutería así adornamos nuestro árbol debemos utilizar primer dos pelos del alambre para poder aguantar y entorchar en la parte de atrás luego que tengamos todos los pelos unidos y con sus piedras uniremos la parte de abajo con la de arriba dándole un poco de vuelta con nuestra pinza .

Step 2: For our other end we will also put the tips in pairs and we will put our jewelry stones so we will decorate our tree we must first use two hairs of the wire to be able to hold and twist on the back after we have all the hairs united and with its stones we will unite the lower part with the upper part, turning it a little with our clamp.

IMG_20220601_163130.jpg

IMG_20220601_163059.jpg

Paso 3: Bueno ya lo más difícil está echo ya estamos en los últimos pasos y don muy fácil para este paso cortaremos un trozo de alambre muy pequeño y aremos un redondito y se lo pondremos a nuestro dije en la parte de arriba .

Step 3: Well, the most difficult part is done, we are in the last steps and it is very easy for this step, we will cut a very small piece of wire and we will make a round one and we will put it on our pendant at the top.

IMG_20220601_163019.jpg

Paso 4: para este último paso cortaremos un trozo de alambre un poco larga y le doblaremos la punta hacien un redondo no muy grande para que no quede muy estrambóticoya teniendo la punta listo entorcharemos el resto del alambre así como lo vemos en la foto del otro lado aremos lo mismo ya listo tomaremos un extremo de nuestro alambre y lo cortaremos con las pinzas y de ese modo enganchamos la otra punta y listo .

Step 4: for this last step we will cut a slightly long piece of wire and we will bend the tip into a round shape that is not too big so that it does not look too outlandish, having the tip ready, we will twist the rest of the wire as we see it in the picture. photo of the other side we will do the same already ready we will take one end of our wire and we will cut it with the tweezers and in this way we hook the other end and that's it.

IMG_20220601_163005.jpg

lista nuestras hermoso dije con piedra de playa , espero que les guste, fue un gusto compartir con ustedes .

list our beautiful charm with beach stone, I hope you like it, it was a pleasure to share it with you.

IMG_20220601_162934.jpg

Todas las Fotos son de mi autoría y fueron tomadas con mi Celular Redmi 9T

All Photos are my authorship and were taken with my Redmi 9T Cellphone