Troubleshooting and Fixing the Leaking and Spitting in Vaping Devices (Tanks) Manual

in #photography6 years ago

http://pipesarsenal.com
Seeping, cracking, spluttering, well it doesn’t obviously have to be part of vaping experience. You can find numerous solutions to decrease frequency of these problems. It doesn’t matter you are vaping with standard tank or rebuildable atomizer, this article can help you to get more satisfaction from vaping despite what kind of vaporizer you are using. It feels very bad when you spill the e-liquid on the hands. These days companies are building their tanks to be less sustainable to leaking issue and some other problems like spluttering. Despite the kind of vaporizer you are using, here are some steps to resolve these issues.
leaking tank.png

Dripping occurs in case e-liquid gets out from the tank, frequently over the airflow system. The cause of leaking influence the amount of e-juice escapes from tank, it can be from couple of drops to losing the complete amount of the e-liquid from your tank. This is the usual issue with many sub-ohm tanks Sub-Ohm Vaping Guide. Top products on the market from the last year, like the SMOK TFV8, Uwell Crown III, Aspire Cleito, gave some problems mentioned above probably because of design mistake or vapers didn’t use them properly. Although there are a several general causes, the nice thing is that there’re techniques to avoid leaking from occuring. We are going to begin from very broad advices, after that we will cover more details for the different vaporizers.

Examine your seal, check if the tank is attached together correctly. Occasionally when you are rushing, you might crossthread the upper cap or neglect to fasten it together sufficiently tight. This might initiate e-liquid to leak out from the gaps. So check if threads are in sync and fastened tightly enough, however not too strong. In case the threads are overlapped, fasten it back together gently.

Take out e-liquid from a chimney – Each tank possesses a main airflow tube that starts from the interior of a tank and goes to the drip tip, the name of this tube is chimney. From time to time you might get e-liquid in the chimney by chance, that frequently causes the bubbling and leaking. When this occurs to you, wipe the chimney with the paper towel and then you can vape.

Hold the tank in vertical straight position – Certain tanks are not designed to be in horizontal position on their side for extended time periods. E-juice might begin leaking out over the airflow holes when you keep it in that position during the night for example. Don’t forget to hold your device upright when you are not vaping for the long periods. So try not to keep your vaporizer horizontally if you don’t want to have leakage issue.

Examine if it has damaged O-rings– The usual reason for leaks. Disassemble the tank, take out the O-rings and check them thoroughly. Try to find any marks of deterioration and damage, defective O-rings. Defective o-rings might be the reason why tank is not completely sealed. However O-rings don’t cost much so you can buy them anytime just don’t forget to get the size you need.
o-rings.png

Don’t forget to close it – When you keep a tank open without a top lid, the e-liquid will seep out from the airflow openings. It happens because of the pressurized environment of tanks. Check if tank is unfilled in case you decide to keep it open without the top lid for some time. You can close the airflow however it’s not good as using the top cap.

Examine the airflow – Every time check if the airflow openings are completely sealed during the filling time. When you are vaping, check if airflow is unseal to let you to actually vape so you don’t have to make big inhales. In case you inhale too strongly, you increase the chance of getting high quantity of e-juice in the coil that might start the leakage.

Be careful during the filling process – Under no circumstances overfill the tank. At all times keep a little air pocket at the top after loading the tank. This hollow volume at the top will stop e-juice from seeping out.

Look for defects – Examine the tank for cracks or any other kind of defects. A tiny fracture in the glass or a section of curved metal might indicate that the tank is not air sealed, letting the e-liquid to seep out and into the air opening regulator. In case the glass is damaged it is typically cheap and easy to get a new one.

e-juice 2.png

Get the proper e-liquid – Some coil heads need high amounts of power, e-juices with less than 70 percent concentration of VG Vegetable glycerinehave high probability of leaking because of the thin viscidness of PG. Usually the big cloud producing vaporizers function fine with seventy percent VG and above, and Mouth To Lung mods are usually function well with less of 70% VG concentration. Never forget to check the e-liquid label to find its ratio.

Examine the coil heads – Unfortunately some factory made products that might have defects. Sometimes the coil can be damaged when you bought it, this might prevent it from keeping the e-liquid well, and this might cause leaking. Step one, check the coil head , if it fastened correctly and in case it is, just swap the coil if possible from a another set to the one you have in the device. In case you still have the issue, then you probably have one of problems that is covered below in this article.

Wick cautiously – This advice is only for rebuildable atomizers that need to be wicked by the vaper himself / herself. Wicking the RTA might be complicated thing, you have to use the right amount of cotton, otherwise you will increase the probability of leakage. The objective is to insert the fabric in to the wick ports avoiding packing them in. This might take some time before you can get it right.

Definition of spitting and cracking

Spitting is the term for the random very hot droplets of e-juice that burst in the mouth during the vaping. When you observe the RDA coil firing, you might occasionally spot this taking place, often complemented by cracking noises. The drips splutter in all directions; however when you are luckless, few of them can get in the mouthpiece.

The origin of spitback: the e-juice gets on the coil and it gets “cooked” and not vaporized as it supposed. This e-liquid splutters like the boiling water spits, and since you are inhaling from a tip, you might as well get a droplet. The issue is strongly related to flooded coils, however in certain circumstances, it might occur even with no flooding. Below you can find few techniques to avoid spitting and bursting from happening.

Priming too much is bad – The definition of Priming the coil is the technique of dripping the e-liquid by hands on a wick afore you will use for the first time. When you pour too much e-liquid in a chamber, you might just initiate flooding problems and spitback. Do not do it too much and determine the right equilibrium. The good rule of thumb is to give some time for the cotton to soak.

Decrease the airflow – Inhaling too strongly during the vaping can cause flooding by actually drawing extra e-liquid in a chamber. Just inhale more gently to avoid this problem, allowing the coil and wicking make the job for you. In case you continue to have problems, then decrease the airflow setting. But, when you decrease the airflow, beware not to inhale too intensely to balance – it can make the problem only worse.

Vape with denser e-liquid – PG is waterier in its nature than VG juice. Because of that it makes sense that great PG concentration e-liquids increase the chance of flooding the atomizer than high VG e-juices. When you have spitback problems, moving to a high VG e-liquid might resolve the issue by decelerating the wicking.

Pound the fire knob – In case you over primed or over dripped – then push the fire button a few times afore you begin to vape. The cracking noises supposed to fade, leaving the normal sounds, white sound like tinkle of vaporization. After that you can start to make hits.

Increase the power – When the wattage is too small, there is a chance you are not vaporizing e-juice as rapidly as the wick is providing it. In this case you can go up by five to ten watts if you are vaping with variable wattage device. Variable Voltage / Variable Wattage Mods Guide

Get a different drip tip – In case you hold the 510 drip tip, then test the anti spitback drip top. Sloping designs do it more difficult for e-liquid to fly straight in your mouth. Additionally lengthier drip tips if they are rounded or twisted can resolve this problem. Also you might mount a screen at the bottom of the drip top.

Clean the funnel – While the flooding is the highly widespread origin of spitback, the issue might get even severer if e-liquid starts to collect in the chimney and then sooner or later travels back down to the coil. It is not difficult to correct this issue: obtain some towel paper, detach the drip tip and insert it in the chimney of the device’s tank. The paper will saturate the surplus e-juice decreasing the probability of spitting and cracking.

Stay away from unusual coils – This advice is for rebuildable atomizers. Multi-feature coils frequently burst and spit because of the design structure. Twisted coils specifically notoriously known for this, however Clapton coils might have similar problems. Their structure can cause for e-juice to pool on a coil, that is why it is difficult to completely avoid bursting on these kinds of coils. The simplest recommendation when you totally wish to prevent spitback is utilizing regular round wire.

Repair the wicks – When you are vaping with RTA and spitback is an issue, you probably have to re-wick the coils. Sometimes it takes some practice time, however the goal is to sheild the channels running from a tank to the chamber without fully jamming them with thickly filled wick. In case you are getting problems with drowning and spitting, then you have to utilize extra wick

Final Thought

Occasionally troubleshooting is crucial for a good vaping experience. Leaking, spitback and hot cracks have many different origins however there are ways to prevent them. Begin with the easy solutions from the start, in case they don’t help, proceed on to more severe solutions. When nothing helps at all then consider to buy a new tank.The good news is that companies start to pay more attention to resolve these wide spread issues. Solutions for spitback and leaking are growing every day. So one day we will not have these problems as technology keeps evolving. For now don’t allow these problems to prevent you from enjoying the vaping.